Free latest Cisco 300-360 exam dumps, valid exam question channel

What is the best way to pass the Cisco 300-360 exam? (First: Exam practice test, Second: Lead4pass Cisco expert.) You can get free Cisco CCNP Wireless 300-360 exam practice test questions here. Or choose: .Study hard to pass the exam easily!

Cisco CCNP Wireless 300-360 Exam Video

Table of Contents:

Latest Cisco CCNP Wireless 300-360 google drive

[PDF] Free Cisco CCNP Wireless 300-360 pdf dumps download from Google Drive:

300-360 WIDESIGN – Cisco:

This exam tests a candidate’s knowledge of identifying customer and application requirements, applying predictive wireless design principles and conducting site surveys needed to design and optimize Enterprise wireless networks.

Latest updates Cisco 300-360 exam practice questions

An engineer is determining powering requirements for a P2P wireless link using Cisco Aironet 1572EC access points.
Which power method is valid for the access point?
A. 802.3af Power over Ethernet
B. Power over Cable
C. Cisco Inline Power
D. 802.3at Power over Ethernet
Correct Answer: B


Which description of Cisco Centralized Key Management is true?
A. It allows the wireless infrastructure to cache the credentials, which eliminates the need to conduct a full
reauthentication when roaming.
B. By caching their credentials, it helps clients save scanning time when looking for a new AP to join.
C. It allows wireless clients to cache their credentials so that, while they are roaming, they don\\’t need to reauthenticate
to the wireless infrastructure.
D. It enables the controller to send directed roam requests to a client in situations when the controller can better service
the client on a different AP than the one to which the client is associated.
Correct Answer: C


When a post-installation audit is performed using the Ekahau Survey tool, which two steps are associated with the
passive portion of the audit? (Choose two.)
A. Check to see if the signal levels on other access points that are heard on the same channel are at least 19 dBm
weaker than the access point that you are next to
B. Survey by SSID to ensure that smooth roaming is taking place
C. Verify that the real-world network traffic (for example, physical data rate, packet loss, etc.) meets user requirements
D. When you have completed the post-installation surveys, compare them to the surveys that were performed before
the installation. They should look nearly identical
E. Verify that user applications are running smoothly over the wireless network
Correct Answer: AD

The wireless team must configure a new voice SSID for optimized roaming across multiple WLCs with Cisco 7925
phones. Which two WLC settings accomplish this goal? (Choose two.)
A. Configure AVC profiles on the SSID
B. Configure mobility groups between WLCs
C. Use AVC to tag traffic voice traffic as best effort
D. Use Cisco Centralized Key Management for authentication
E. Configure AP groups between WLCs
Correct Answer: BD


What is the result if a client radio is incapable of supporting all the 5 GHz channels you have deployed in the controller
or APs?
A. You may only be able to deploy 20 MHz-wide channels.
B. This may result in the client having to roam more frequently to find a channel it supports.
C. This may result in coverage holes in the network.
D. You may only be able to deploy 40 MHz-wide channels.
Correct Answer: C


If you are calibrating for 2.4 GHz and the site will not be using 802.11 and 802.11b data rates, what should be done to
ensure an accurate calibration?
A. Make sure that the access points have the unused rates disabled.
B. Make sure that you are using an 802.11b client when calibrating.
C. Make certain that there are no legacy clients when performing the calibration because they will disrupt the process.
D. Make sure to use a client that supports both 802.11b/g and 802.11a.
Correct Answer: A


When designing and deploying an outdoor mesh network, what is the appropriate RF cell overlap?
A. 10 percent
B. 15 percent
C. 20 percent
D. 25 percent
E. Application dependent
Correct Answer: E


When designing a WLAN, AP placement is important. Which option describes how to rank the density of APs needed to
support location services versus data and voice services?
A. Data services have the lowest density of APs compared to location services, which has the highest density.
B. Data services have a lower density of APs compared to location services, but more than voice.
C. Voice services have the highest density of APs over location and data services.
D. Voice and data services require a higher density of APs than location services.
Correct Answer: A


What is the Cisco-recommended cell overlap percentage for a typical RToWLAN network design?
A. 5 to 10
B. at least 20
C. a maximum of 20
D. at least 50
Correct Answer: B


A downstream packet that contains a DSCP value arrives at the WLC Ethernet interface from the wired source network.
The WLC is configured for QoS WLAN 802.1p mapping. How does the WLC treat the CAPWAP QoS marking when
leaving the controller interface for the respective AP and final wireless client destination?
A. No outer CAPWAP or inner QoS tagging is applied.
B. The outer CAPWAP CoS is marked and capped and the inner DSCP maintains the original marking.
C. No outer CAPWAP QoS tag is applied, but the original DSCP is maintained inside CAPWAP.
D. The outer CAPWAP DHCP is marked and capped without any inner DSCP value.
Correct Answer: B


A corporation has a Cisco Unified Wireless Network that has been deployed for voice coverage. The wireless data rates
have been tuned to mandatory rates of 18 Mbps and 36 Mbps. Some wireless clients have been experiencing drops
streaming multicast video while moving throughout the building. What is the cause of the drop in video?
A. Clients are maintaining a 12Mbps rate and cannot receive the stream at 18Mbps.
B. Clients are not roaming due to coverage. This is causing the multicast data to drop due to the client re-associating
C. Clients are roaming at lower data rates and are not maintaining 36Mbps connectivity.
D. Clients are connected at 18Mbps; however, other clients are connecting at 12Mbps and are causing the multicast
video to degrade.
Correct Answer: C


An engineer is implementing Q0S for a new wireless voice network. Which two considerations should be identified first?
(Choose two.)
A. QoS marking
B. policing
C. QoS requirements
D. data traffic usage
E. traffic classification
Correct Answer: CE


What two factors could cause a post-deployment audit to show a high retransmission rate for the WLAN? (Choose two.)
A. CRC errors
B. Rate shifting
C. CCX compatible clients
D. High SNR values
E. High RSSI values
Correct Answer: AB

Related 300-360 Popular Exam resources

titlepdf youtube Cisco lead4pass Lead4Pass Total Questions
Cisco CCNP Wireless lead4pass 300-360 dumps pdf lead4pass 300-360 youtube 300-360 WIDESIGN – Cisco 221 Q&A
lead4pass 300-370 dumps pdf lead4pass 300-370 youtube 300-370 WITSHOOT – Cisco 124 Q&A
lead4pass 300-375 dumps pdf lead4pass 300-375 youtube 300-375 WISECURE – Cisco 148 Q&A
lead4pass 300-365 dumps pdf lead4pass 300-365 youtube 300-365 WIDEPLOY – Cisco 144 Q&A

Lead4Pass Year-round Discount Code

lead4pass coupon

What are the advantages of Lead4pass?

Lead4pass employs the most authoritative exam specialists from Cisco, Microsoft, CompTIA, IBM, EMC, etc. We update exam data throughout the year. Highest pass rate! We have a large user base. We are an industry leader! Choose Lead4Pass to pass the exam with ease!

why lead4pass


It’s not easy to pass the Cisco 300-360 exam, but with accurate learning materials and proper practice, you can crack the exam with excellent results. provides you with the most relevant learning materials that you can use to help you prepare.